Announcement

Collapse
No announcement yet.

Water Pump

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Chicken Hawk
    replied
    Back in the '60's at the Indy drags one Sunday a fellow working on his race car was revving the engine a fan blade came off hit him in the chest and killed him.

    Ted

    Leave a comment:


  • Skip Lackie
    replied
    Many years ago John Poulos had a ~41 Cadillac 60 Special that threw a fan blade. Sliced right through the hood and landed in the street.

    Leave a comment:


  • Ron Dame
    replied
    Yes. I neighbor has a 1970 Dodge truck with an interesting dent and cut on the hood from a fan that let go. I'm replacing a fan on a 1970 Volvo that has a cracked blade. I found out by it's buzzing. Maybe only 1970 cars of any make have this problem. ;-)

    Originally posted by adamevans View Post
    Thanks guys.

    Stress cracks in a metal fan?

    Leave a comment:


  • RadioRoy
    replied
    Some of the fans can develop cracks around the bolt holes. If/when they get bad enungh, the fan blades can fly off at speed and hit the hood, radiator, or your head if you have the hood open.

    Leave a comment:


  • adamevans
    replied
    Do I need to torque the bolts down?

    Leave a comment:


  • skyway
    replied
    ...and also be sure that the weep hole is oriented down at 6 o'clock.
    The 4 bolts are evenly spaced so that you can get this wrong!

    Leave a comment:


  • 55 56 PREZ 4D
    replied
    Years ago there was a run of pumps that were assemble with the impeller installed incorrectly.
    http://www.studebaker-info.org/tech/.../S1048x2x1.jpg
    Shows the service letter with the correct dimension.
    Always a good thing to check and move the impeller if needed.
    If the impeller needs to be repositioned, use a gear puller to move it away from the housing.
    Never move the shaft from the bearing.
    The Studebaker Tech site http://www.studebaker-info.org/rjtechoct2014p1.html is an incredible source of information

    Leave a comment:


  • adamevans
    replied
    Thanks guys.

    Stress cracks in a metal fan?

    Leave a comment:


  • doofus
    replied
    And while doing this carefully inspect the fan blade for stress cracks. Luck Doofus

    Leave a comment:


  • StudeRich
    replied
    I do not think there could possibly be an easier car to replace a Water Pump on.

    There are no Radiator Hoses, Fan Shrouds, Water Manifolds, nothing to remove except the small Pump itself and the Fan, Spacer and Pulley.

    The 4 Bolts do require Copper Sealing Washers always supplied with Quality New Pumps from Studebaker Vendors. The Gasket should be as thin as possible to allow minimum clearance at the back of the Water Manifold.

    Leave a comment:


  • Warren Webb
    replied
    Just about the easiest water pump ever made to replace. 4 bolts & remove the fan assembly. 4 bolts & the water pump is removed from the water manifold. Clean the 4 gasket surfaces & install the new pump with the supplied copper washers (providing you got your new pump from one of our vendors), reinstall the fan assembly, add coolant & your done! Welcome to the forum!!!!!

    Leave a comment:


  • adamevans
    started a topic Cool/Heat: Water Pump

    Water Pump

    Hi guys! I'm new to Studebakers, and I wanted to check with you to see if there was anything I should keep in mind when changing my water pump. My car is a 64 Lark Cruiser with the v8.

    Is it a pretty straightforward rip and replace?
Working...
X