Announcement

Collapse

Get more Tips, Specs and Technical Data!

Did you know... this Forum is a service of the Studebaker Drivers Club? For more technical tips, specifications, history and tech data, visit the Tech Tips page at the SDC Homepage: www.studebakerdriversclub.com/tips.asp
See more
See less

1952 rubber parts

Collapse
This topic is closed.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • tbredehoft
    replied
    Steele Rubber has a preformed 'T' shaped molding that can be made to fit almost everything.

    URL

    www.Steelrubber.com

    Product

    Maybe Mounting Pad Stock 70-0308-17

    It worked around the tail light housings on my '53 coupe and the trunk lift bar.

    Tom Bredehoft
    '53 Commander Coupe
    '60 Lark VI
    '05 Legacy Ltd Wagon
    All Indiana built cars

    Leave a comment:


  • N8N
    replied
    if you can't find one, just glue some fender welt to the backside of the handle...

    nate

    --
    55 Commander Starlight
    62 Daytona hardtop
    http://home.comcast.net/~njnagel

    Leave a comment:


  • Michidan
    replied
    yea...! Not the trunk seal, got that OK. Just the gasket behind the handle/emblem/trim piece thingy.
    I guess I will make one also. I just wasn't sure it was a gasket the whole length of the part, or small rubber washers around the 4 studs. all that was left of the orginal was just around the studs.
    So thanks for the description, it helps.

    haven't contacted hennesy yet RE the taillamp gaskets...

    Dan
    52 hardtop

    Leave a comment:


  • BRUCESTUDE
    replied
    I have made a trunk handle gasket for a couple of different '52s. I use some sheet neoprene rubber found at a great Ma and Pa hardware store. This stuff is about 1/8" thick, and really protects the paint! I traced and cut the main (center)gasket using an old one as a pattern. The ends are basically smaller round pieces that have a hole to slip over the stud. I have a set of hole punches to make the stud holes.

    Leave a comment:


  • rockne10
    replied
    I didn't think of that, Gary. You're probably right. We did a 52 and had to make a pad for the handle from an innertube. I forget how we handled the tailight seals. I'll have to look next time the car comes in to the shop.

    Leave a comment:


  • studegary
    replied
    I think that he means the trunk handle gasket, not the trunk lid seal. Is my assumption correct, Michidan?

    Gary L.
    1954 Commander Starliner (restomod)
    1959 DeLuxe pickup (restomod)

    Leave a comment:


  • Michidan
    replied
    Seems like the 50 or 51 molding kicks up at the ends. 52 molding doesn't. Could be other differences too, I've only got the 52 piece to look at.

    Dan
    52 hardtop

    Leave a comment:


  • rockne10
    replied
    I don't know about the tailight seals but the trunk seal should be the same 50, 51 or 52.

    Leave a comment:


  • whacker
    replied
    Contact Fennessey of Tennessee. Advertises in Turning Wheels.

    Leave a comment:


  • Guest's Avatar
    Guest started a topic 1952 rubber parts

    1952 rubber parts

    Anyone know of a source for 1952 Champion tail light seals and the trunk molding gasket? Seems SI and Sasco have most other years but us 52ers are a little left out.

    I guess I can make the trunk molding gasket because I sure don't want to hang this heavy thing on my pretty new paint. What are the chances anyone can give me an idea or picture on what it was like? The Sasco online pics for 50 and 51 seem to cover the whole mating area.

    Dan
    52 hardtop
Working...
X