Announcement

Collapse

Get more Tips, Specs and Technical Data!

Did you know... this Forum is a service of the Studebaker Drivers Club? For more technical tips, specifications, history and tech data, visit the Tech Tips page at the SDC Homepage: www.studebakerdriversclub.com/tips.asp
See more
See less

Remanufatured Studebaker motors

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • studelover
    replied
    Mike how much is your rebuild? Let's say I sent you my core could you send me an engine ready for installation?

    Studebakers forever!

    Leave a comment:


  • raprice
    replied
    Does Bill Cathcart do V-8's? I know his expertise is Champion engines. I do know that he stocks some V-8 parts.
    Rog

    '59 Lark VI Regal Hardtop

    Leave a comment:


  • Roscomacaw
    replied
    I'm gonna be installing a 289 short block in my Transtar that Ken built for me about 2 years ago. I have a couple sets of reworked heads lying about, so I'll slap on a set of those and put in a fresh clutch as well.
    Ken's approach to engine building frustrates me sometimes The guy's too damned meticulous!
    More than once I've said "Aw **** Ken, it'll be just fine like that."
    Ken'll give me the look and then he'll say something like "Yeah, but I can't put it back together like that."

    Miscreant adrift in
    the BerStuda Triangle


    1957 Transtar 1/2ton
    1960 Larkvertible V8
    1958 Provincial wagon
    1953 Commander coupe

    Leave a comment:


  • showbizkid
    replied
    Yeah, the pins were left off by the last "rebuilder" who messed with it. That's one reason the transmission went south Look at this flex plate:



    The trans is a FOM. I know the block is original and I think the trans is too, but I'm going to dial it in anyway.


    [img=left]http://members.cox.net/clarknovak/lark.gif[/img=left]

    Clark in San Diego
    '63 F2/Lark Standard
    http://studeblogger.blogspot.com

    Leave a comment:


  • studelover
    replied
    I was looking at the pic's of your motor and I don't see any dow pins on the back of the engine. how is this motor attached and if automatic what is this trans call?
    quote:Originally posted by showbizkid

    quote:Originally posted by HNCadet

    Okay Clark, you've piqued my interest, Is it a commercial shop, or some local Studies?
    Local Studie, but he's got 40 years experience building Stude engines! His name is Ken Pyle and he's near Visalia, CA. You can see pix of my 259 at http://s132.photobucket.com/albums/q...0home/?start=0

    You can reach him at 559-561-6115.


    [img=left]http://members.cox.net/clarknovak/lark.gif[/img=left]

    Clark in San Diego
    '63 F2/Lark Standard
    http://studeblogger.blogspot.com
    Studebakers forever!

    Leave a comment:


  • PackardV8
    replied
    Greetings, All,

    FWIW, I have my work done by a back-to-the-land auto machinist in the middle of nowhere who does great work at very reasonable prices. His low overhead means low prices for cleaning, line-boring, decking, boring, honing, grinding the crank and doing the heads, would be less than $1500. Naturally, parts, assembly and shipping are additional.

    Anyone wanting a Studebaker performance rebuild, e-mail me off-list at PackardV8@comcast.net

    thnx, jv.

    PackardV8

    Leave a comment:


  • showbizkid
    replied
    quote:Originally posted by HNCadet

    Okay Clark, you've piqued my interest, Is it a commercial shop, or some local Studies?
    Local Studie, but he's got 40 years experience building Stude engines! His name is Ken Pyle and he's near Visalia, CA. You can see pix of my 259 at http://s132.photobucket.com/albums/q...0home/?start=0

    You can reach him at 559-561-6115.


    [img=left]http://members.cox.net/clarknovak/lark.gif[/img=left]

    Clark in San Diego
    '63 F2/Lark Standard
    http://studeblogger.blogspot.com

    Leave a comment:


  • HNCadet
    replied
    Okay Clark, you've piqued my interest, Is it a commercial shop, or some local Studies?

    Leave a comment:


  • DEEPNHOCK
    replied
    Not at Jasper prices, especially for this crowd
    Jeff[8D]

    quote:Originally posted by studelover

    I know that jasper remanu chevy and ford motors question is there anyone doing this for Studebaker 289 motors and transmissions? There has to be somebody![8D]
    Studebakers forever!


    DEEPNHOCK at Gmail.com
    Brooklet, Georgia
    '37 Coupe Express (never ending project)
    '37 Coupe Express Trailer (project)
    '61 Hawk (project)
    http://community.webshots.com/user/deepnhock

    Leave a comment:


  • showbizkid
    replied
    I can recommend a rebuilder if you're in Central/Southern California!


    [img=left]http://members.cox.net/clarknovak/lark.gif[/img=left]

    Clark in San Diego
    '63 F2/Lark Standard
    http://studeblogger.blogspot.com

    Leave a comment:


  • Kdancy
    replied
    Thought of doing this myself. But after putting 2,450.00 into doing a 289 just for the machine work, (the engine was balanced and the block decked and line bored) I think you would be hard pressed to build one right and not have it setting for a while. Looks to me you would have around 3,000 to 3,600 by the time parts are added. Still may pay to have a few short blocks done up.

    Leave a comment:


  • studelover
    started a topic Remanufatured Studebaker motors

    Remanufatured Studebaker motors

    I know that jasper remanu chevy and ford motors question is there anyone doing this for Studebaker 289 motors and transmissions? There has to be somebody![8D]

    Studebakers forever!
Working...
X