Announcement

Collapse

Get more Tips, Specs and Technical Data!

Did you know... this Forum is a service of the Studebaker Drivers Club? For more technical tips, specifications, history and tech data, visit the Tech Tips page at the SDC Homepage: www.studebakerdriversclub.com/tips.asp
See more
See less

question on hawk and commander frame

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • studegary
    replied
    quote:Originally posted by N8N

    Also the rear springs changed in 1958 at the same time that the one piece driveshaft was introduced. So any 58-up Hawk frame should work OK. An earlier frame would require that the later spring mounts be transferred over and the center driveshaft support be cut out.

    good luck

    nate
    Nate/N8N - How are you going to adjust for the 7.5 inch difference in wheelbase between the two frames that he is asking about?

    Gary L.
    Wappinger, NY
    1954 Commander Starliner (restomod)
    1959 DeLuxe pickup (restomod)

    Leave a comment:


  • N8N
    replied
    Also the rear springs changed in 1958 at the same time that the one piece driveshaft was introduced. So any 58-up Hawk frame should work OK. An earlier frame would require that the later spring mounts be transferred over and the center driveshaft support be cut out.

    good luck

    nate

    --
    55 Commander Starlight
    http://home.comcast.net/~njnagel

    Leave a comment:


  • skip
    replied
    quote:Originally posted by R2Andy

    Those frames are in no way interchangable. The '64 Y body has a 113" wheelbase, the '58K body has a 120.5" wheelbase. All domestic 6 and V8 4 door frames were 11 guage, as were all JT And JTS powered cars. The 6 cyl. 2 door (F body) is the only one to get the 14 guage frame while the V8 2 door (F body) got the 13 guage frame. As far as I can remember, all '53 to '64 K body frames should interchange. The only real difference is that the '57 and earlier frames had a different crossmember to support the 2 piece drive shaft. '58 and newer had the one piece driveshaft.
    thanks very much. skip.

    R2Andy

    Leave a comment:


  • skip
    replied
    quote:Originally posted by Alan

    No, different WB. Should be 13ga or about .083" Depends on if you live in Michigan or Arazona.
    thank you very much.

    Leave a comment:


  • R2Andrea
    replied
    Those frames are in no way interchangable. The '64 Y body has a 113" wheelbase, the '58K body has a 120.5" wheelbase. All domestic 6 and V8 4 door frames were 11 guage, as were all JT And JTS powered cars. The 6 cyl. 2 door (F body) is the only one to get the 14 guage frame while the V8 2 door (F body) got the 13 guage frame. As far as I can remember, all '53 to '64 K body frames should interchange. The only real difference is that the '57 and earlier frames had a different crossmember to support the 2 piece drive shaft. '58 and newer had the one piece driveshaft.


    R2Andy

    Leave a comment:


  • Alan
    replied
    No, different WB. Should be 13ga or about .083" Depends on if you live in Michigan or Arazona.

    Leave a comment:


  • skip
    started a topic question on hawk and commander frame

    question on hawk and commander frame

    hi. im trying to find out if the frame for a 64 commander 6 cyl 4 door is the same as a 58 packard hawk. also what would be the frame gauge on the 64?. is it too light because it is a 6 cyl?. thanks for any help. email shiftknob@verizon.net
Working...
X