Announcement

Collapse

Get more Tips, Specs and Technical Data!

Did you know... this Forum is a service of the Studebaker Drivers Club? For more technical tips, specifications, history and tech data, visit the Tech Tips page at the SDC Homepage: www.studebakerdriversclub.com/tips.asp
See more
See less

It just looks better..............Studebaker Avanti and others.............p/s cover grommet

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hawklover
    replied
    Amazing!......just scored ten of the little buggers..........just looked under a different application!! Click image for larger version

Name:	Scan0005.jpg
Views:	103
Size:	53.8 KB
ID:	1804351

    Leave a comment:


  • Hawklover
    replied
    Thanks for the update!

    Leave a comment:


  • WCP
    replied
    Pardon my slow memory in recalling the vent detail pertaining to flat rubber gasket and flat washer listed as "#1548198 Washer (special)". The flat washer is special due to a radial slot or groove, approx. 1/16" wide and about the same in depth on the back side, providing the needed venting channel for the reservoir. Today most of those washers have been swapped for plain flat washer, defeating the necessary venting. The lack of slot is easy to rectify with a hacksaw blade or dremel tool.

    Leave a comment:


  • bensherb
    replied
    The grommet that goes in the rocker cover for the studs to pass through works great for the power steering cover too. The Ford filler cap (which for some reason the Studebaker does not have ) has a vent in it.

    Leave a comment:


  • Hawklover
    replied
    Here it is!!
    Attached Files

    Leave a comment:


  • Skip Lackie
    replied
    The ones I got years ago from N&A were T-shaped and fit down in the hole in the lid.

    Leave a comment:


  • Hawklover
    replied
    Originally posted by Skip Lackie View Post
    Stude actually called it a gasket: part number 1553299.
    Not the same, this is a flat piece of rubber, not a rubber grommet.

    Leave a comment:


  • Skip Lackie
    replied
    Stude actually called it a gasket: part number 1553299.

    Leave a comment:


  • Hawklover
    replied
    Well if what you claim is in fact true, then why is this grommet not listed in the Avanti or any other Stude parts book?

    Leave a comment:


  • StudeRich
    replied
    Guess what, that is actually the CORRECT Studebaker Grommet! Cars without it are WRONG/ Modified!

    Leave a comment:


  • Hawklover
    replied
    Originally posted by WCP View Post
    Make sure that you are not blocking the vent or pressure release path for the reservoir.
    Great heads up..........the grommet is hollow in the middle;-)

    Leave a comment:


  • WCP
    replied
    Make sure that you are not blocking the vent or pressure release path for the reservoir.

    Leave a comment:


  • It just looks better..............Studebaker Avanti and others.............p/s cover grommet

    Now I know I am anal but.........below the wing nut Studebaker utilized a flat plain washer and below the washer a flat piece of rubber.......a better method (thanks to FoMoCo) was a great rubber grommet that when faced down actually fits into the top of the p/s cover, and then your flat steel washer goes on top and is pushed down by the wing nut. I have never liked using just the flat piece of rubber Studebaker used........Ford had a better idea!
    Grommet is Fel-Pro number: 10740. Yes I know its no big deal..........but like I said I am anal about anything on my Avanti;-)
    Last edited by showbizkid; 09-23-2019, 07:14 AM.
Working...
X