Announcement

Collapse
No announcement yet.

Getting the hood open--60 Lark

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • 60ragtop
    replied
    Yep, what happened is the clip holding the cable popped loose. To prevent this from happening again, I screwed it down which should have been done in the first place. By the way, rather than use a long screwdriver from below to lever the latch over, a frustrating process, I found it much easier to simply use a hack saw blade as a slim jim. Just lever the hood up a little bit with a screw driver (cover the paint with tape to avoid any scratching) so you can see the latch, insert the blade thru the hood opening and push toward the driver's side against the latch. Voila!! The hood popped open.

    Leave a comment:


  • Boothguy
    replied
    I have the same problem but the cable didn't break, it was the clip that secures the cable next to the latch. Is that clip available? Thanks

    Leave a comment:


  • showbizkid
    replied
    FWIW, two preventative measures those of us with cable hood releases can take:

    1) Studes are some of the very few cars that use release cables that can actually be lubed! Take a can of silicone spray (NOT WD-40) and soak the wire-wrap case of the cable, then work it back and forth a few times. It will free up nicely and be much less prone to breakage than if left unlubricated after 40 years This also works on Climatizer cables, BTW. I just freed up a very old, corroded set this way.

    2) Several StudeVendors stock replacement hood release cables. See my note about 40 year old unlubricated cables above! I just bought a NOS cable and plan to install it even though my original cable appears to work well... better safe than sorry.


    [img=left]http://members.cox.net/clarknovak/lark.gif[/img=left]

    Clark in San Diego
    '63 F2/Lark Standard
    http://studeblogger.blogspot.com
    www.studebakersandiego.com

    Leave a comment:


  • barnlark
    replied
    I haven't had that problem yet, but checked it out on mine and it is pretty easy to access with a good light and a little luck per those instructions. Great link for info, Clark. Be prepared..[^]

    Leave a comment:


  • showbizkid
    replied
    Check here for step-by-step instructions:

    https://www.studebakerparts.com/stud...h-control.html


    [img=left]http://members.cox.net/clarknovak/lark.gif[/img=left]

    Clark in San Diego
    '63 F2/Lark Standard
    http://studeblogger.blogspot.com
    www.studebakersandiego.com

    Leave a comment:


  • 59r2
    replied
    Frank,
    this is a problem but not a nightmare, go slow.
    The first thing to do is put a blanket on the hood and on top of thisput a 80lb bag of cement or sand or anything heavy enough to take presure off the lever . Next get a coat hanger and straighten out,next get apiece of 1/4 or 3/16 round stock. Bend the hanger to a kind of s shape \ 3/4"back
    2 to 3 inch /
    ------------------/ 1 1/2"up
    /
    /
    /
    /
    / handle
    /
    /
    work this thur about the secound or third row of grill mesh in front of the lock to go thur the the small opening where the cable attaches to the lock mechanism bend accordinly to make it work when you feel the resistance of the latch lever stop and make the thicker rod to this shape .Wiggle in there while light pressing down on the hood it should release. It's been about twenty years since I had to do this to my 60convert I hope I am remembering this right ,if this dosen't work let me know I'll take a drive up to my other garage and check out the mechanism for you.
    JOE









    1959 HARDTOP R2 clone
    1960 conv
    SDC member since 1972

    Leave a comment:


  • 60ragtop
    replied
    Thanks, Gary. I refined my search and found some instructions on chuck collins' site. Now I have to see if I can understand them well enough to get the hood open...

    Leave a comment:


  • studegary
    replied
    I think that up from the bottom with something like an extra long screwdriver or slim pry bar is going to be your best shot at this.

    Gary L.
    Wappinger, NY

    SDC member since 1968
    Studebaker enthusiast much longer

    Leave a comment:


  • 60ragtop
    started a topic Getting the hood open--60 Lark

    Getting the hood open--60 Lark

    There must be an easy way to do this. Apparently the hood release cable on my 60 Lark Convertible has come loose and won't release the hood. Is there a method I can use to reach through the grill to somehow release the catch? This is a convert with the extra bracing behind the grill, so reaching up from the bottom is a problem. Any answers welcome--this car is in a parade Thursday and I need to get under the hood pronto. By the way I did try the search mechanism but didn't find anything for the '60 Larks.

    Frank
Working...
X