Announcement

Collapse

Get more Tips, Specs and Technical Data!

Did you know... this Forum is a service of the Studebaker Drivers Club? For more technical tips, specifications, history and tech data, visit the Tech Tips page at the SDC Homepage: www.studebakerdriversclub.com/tips.asp
See more
See less

hawk suspension 2

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Guest's Avatar
    Guest replied
    Thanks All

    I have borrowed a couple of LARGE lads to sit on the front bumper
    after I loosened all bolts.The car has now lowered to an acceptable level,so all bolts have been tightened and grease as required.
    IT seems to be holding,just have to replace the stabiliser bar.

    Thanks

    bill j

    Leave a comment:


  • unclemiltie
    replied
    I just replaced the bushings and springs on a 64 convertible, I took the shock out and put a 5/8 inch threaded steel rod down the center to compress the spring, i had the car on jack stands, i attached the top a-arm first letting all bolts etc loose, i then used a floor jack to help pursuade the lower a-arm to go into place so I could get the bottom four bolts in. I did not tighten any bolts tight till everything was in place. you have to have the car with engine sitting on the ground before you tighten the bushing bolts. good luck, was not as easy as when i was younger

    Milt

    1947 Champion (owned since 1967)
    1961 Hawk
    1964 Convertable
    1967 Avanti

    Leave a comment:


  • kmul221
    replied
    OOP's ! I forgot about the front sway bar disconnect,needing to be included

    Leave a comment:


  • kmul221
    replied
    If the upper & lower "A" arm bolts to frame have been removed,the tie rod & brake line disconnected,the spring must be compressed & held by a proper tool.The unit should lift out as a complete section,spindle,upper & lower "A" arms.Thats how I did the upper & lower bushings,without moving the outer excentrics

    Leave a comment:


  • DEEPNHOCK
    replied
    Shocks rusted/frozen?





    DEEPNHOCK at Gmail.com
    Brooklet, Georgia
    '37 Coupe Express (never ending project)
    '37 Coupe Express Trailer (project)
    '61 Hawk (project)
    http://community.webshots.com/user/deepnhock

    Leave a comment:


  • sbca96
    replied
    Springs dont get stronger, thats for sure! Its possible that the
    outer bushings (upper & lower) have seized from sitting. Loosening
    the caps wont get you anything (if anything it could cause some MORE
    problems). Do the bushings "take" grease?

    What prompted the issue? Car sitting to high in the front? Is the
    front end complete, IE engine is there? The groaning could come from
    the inner bushings being worn out, cracked, or off "center".

    Tom

    '63 Avanti, zinc plated drilled & slotted 03 Mustang Cobra 13" front disc/98 GT rear brakes, 03 Cobra 17" wheels, GM alt, 97 Z28 leather seats, soon: 97 Z28 T-56 6-spd, Ported heads w/SST full flow valves, 'R3' 276 cam, Edelbrock AFB Carb, GM HEI distributor, 8.8mm plug wires

    Leave a comment:


  • bill j
    started a topic hawk suspension 2

    hawk suspension 2

    G'day all

    Posted a few weeks back regarding the front suspension problems I am having.Have tried a few things but to no avail.
    At present I have removed all the upper and lower inside A arm bolts and loosened the outer cap nuts.When I lift the bottom A arm near the kingpin,the top A arm only moves 11/2" before the weight of the car is off the stand.This movement is accompanied by a lot of groaning and it's not just me.Could the spring have got stronger by not having any weight on it in 30 years? It seems to be the original spring with part number and the notch in the bottom coil.I am just running out of ideas





    bill j
Working...
X