Announcement

Collapse
No announcement yet.

57 GH Throttle Pressure rod spring clip needed

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • kirkdob
    replied
    Originally posted by jg61hawk View Post
    I was looking around for you and so far that is all I found. I did find several suggestions though and two good ones were:

    Use small wire ties around the elongated clip. OR
    Take a small hose clamp cut a slot in it for the rod and tighten that around the bad clip.

    OK I'll leave you alone unless I find the exact clip.
    I appreciate your time and effort. I'm going to take the picture I posted to an auto parts store, maybe they have a bulk assortment. It can't be that strange an item, right?

    Leave a comment:


  • jg61hawk
    replied
    I was looking around for you and so far that is all I found. I did find several suggestions though and two good ones were:

    Use small wire ties around the elongated clip. OR
    Take a small hose clamp cut a slot in it for the rod and tighten that around the bad clip.

    OK I'll leave you alone unless I find the exact clip.

    Leave a comment:


  • kirkdob
    replied
    Originally posted by jg61hawk View Post




    555-15740
    Carb Linkage Swivel Fits 1/4"-28 RH thottle linkage rod <LI sizcache="0" sizset="19">1/4"-28 RH Male x 1/4"-28 Female
    View this item
    $4.49
    Ships
    Today

    This is from JEGGS.
    555-15741
    Carb Linkage Swivel Fits 1/4"-28 LH thottle linkage rod <LI sizcache="0" sizset="24">1/4"-28 LH Male x 1/4"-28 Female
    View this item
    $5.99
    Ships
    Today
    The picture shows the clip I need. It's the semi circular spring clip as shown in the picture. If I can't find one I may just buy this and see if it fits.
    Attached Files

    Leave a comment:


  • jg61hawk
    replied




    555-15740
    Carb Linkage Swivel Fits 1/4"-28 RH thottle linkage rod <LI sizcache="0" sizset="19">1/4"-28 RH Male x 1/4"-28 Female
    View this item
    $4.49
    Ships
    Today

    This is from JEGGS.
    555-15741
    Carb Linkage Swivel Fits 1/4"-28 LH thottle linkage rod <LI sizcache="0" sizset="24">1/4"-28 LH Male x 1/4"-28 Female
    View this item
    $5.99
    Ships
    Today

    Leave a comment:


  • kirkdob
    replied
    Originally posted by jg61hawk View Post
    I may be wrong...but isn't there a groment and a clip.. Stude International has the groment that would make the rod tight. I might be thinking of the actual shift groment or the kick down groment. Usually anything clipped has help to keep it tight. I have a 61 so we are close but not exact.
    The crank has a ball and the rod has a socket. There is a spring clip that slips over the rod to capture the ball and keep it in the socket.

    Leave a comment:


  • jg61hawk
    replied
    I may be wrong...but isn't there a groment and a clip.. Stude International has the groment that would make the rod tight. I might be thinking of the actual shift groment or the kick down groment. Usually anything clipped has help to keep it tight. I have a 61 so we are close but not exact.

    Leave a comment:


  • kirkdob
    started a topic 57 GH Throttle Pressure rod spring clip needed

    57 GH Throttle Pressure rod spring clip needed

    The rod frequently falls off at the front ball socket. The spring clip that goes around the rod is shot. Does anyone know where I can get a new clip?
Working...
X