Announcement

Collapse
No announcement yet.

repro C/K front fenders

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • 63t-cab
    replied
    Ya I've seen those and they get twisted and flattened and over bent.though as above I'd like to see a inner/outer unit dead nuts on,then grafted in.

    Joseph R. Zeiger

    Leave a comment:


  • Milaca
    replied
    But the patch doesn't include the bolt mounting flange.


    Brent's rootbeer racer.
    MN iron ore...it does your body good.

    Leave a comment:


  • Andy R.
    replied
    quote:Originally posted by 63t-cab

    My thought for some time now has been this.what if patch panels were made for the rear section of front fenders?I mean a complete section,the inner and outer spot welded together,and weld that unit to the origional fender,I also mean a panel assembly that fits lkie to factory parts would mate!!! I'm kinda surprised C.E. did'nt do this.

    Joseph R. Zeiger
    Classic Enterprises DOES offer a vertical patch panel for the usual rust area...for $75 each
    Pass. side shown here.

    Here's a link (scroll halfway down): http://www.classicent.com/coupes_hawks.php

    Andy
    62 GT

    Leave a comment:


  • studegary
    replied
    quote:Originally posted by 63t-cab

    My thought for some time now has been this.what if patch panels were made for the rear section of front fenders?I mean a complete section,the inner and outer spot welded together,and weld that unit to the origional fender,I also mean a panel assembly that fits lkie to factory parts would mate!!! I'm kinda surprised C.E. did'nt do this.

    Joseph R. Zeiger
    This is close to the way that we repaired C/K fenders, that had a rusty rear section, years ago. We would cut and flange the original fender at the top of the wheel opening. Then we would cut an NOS fender at the same point and replace the rear half on the car. It would have been a lot more labor to replace the entire fender. Yes, I know that it used up NOS fenders, but they were plentiful then (early 1970s).

    Gary L.
    Wappinger, NY

    SDC member since 1968
    Studebaker enthusiast much longer

    Leave a comment:


  • Milaca
    replied
    If reproduction Studebaker bodyparts were made in China, I doubt if anybody would be happy. They likely wouldnt fit, they wouldnt look original, they would be covered in lead-based primer, and they would be produced from lighter gauge steel. Okay, I'm being prejudice, but I've had a lot of unhappy experiences with Chinese made items. [B)]


    Brent's rootbeer racer.
    MN iron ore...it does your body good.

    Leave a comment:


  • 63t-cab
    replied
    My thought for some time now has been this.what if patch panels were made for the rear section of front fenders?I mean a complete section,the inner and outer spot welded together,and weld that unit to the origional fender,I also mean a panel assembly that fits lkie to factory parts would mate!!! I'm kinda surprised C.E. did'nt do this.

    Joseph R. Zeiger

    Leave a comment:


  • JDP
    replied
    quote:Originally posted by Dan White

    Seeing as NOS front C/K fenders are going for over $1K per these days (note a recent ebay auction, as well as other private party sales that were the same or even higher). It would seem that someone w/ some $$ could use a set of NOS fenders to have some off shore company start making these again. Having worked on early Camaro/Firebirds most of the body panels are now available as repros and many of them are pretty good quality. Some I bought a few years ago were stamped in Belgium, but I think many are now are Chinese or even US. I know the market for these is much larger but I am sure there would be quite a bit of interest if they were available. I know there are fiberglass ones out there but they are just not the same as metal.

    Dan White
    64 R1 GT
    64 R2 GT
    The tooling for several 1000 fenders might make sense economically, but a few 100 even at several $1000 a pop is out of the question. $1000 each is the price for reproduced 55 Chevy fenders with a much bigger market, maybe when NOS Studebakers reach 5K each.

    JDP/Maryland

    Leave a comment:


  • Dan White
    started a topic repro C/K front fenders

    repro C/K front fenders

    Seeing as NOS front C/K fenders are going for over $1K per these days (note a recent ebay auction, as well as other private party sales that were the same or even higher). It would seem that someone w/ some $$ could use a set of NOS fenders to have some off shore company start making these again. Having worked on early Camaro/Firebirds most of the body panels are now available as repros and many of them are pretty good quality. Some I bought a few years ago were stamped in Belgium, but I think many are now are Chinese or even US. I know the market for these is much larger but I am sure there would be quite a bit of interest if they were available. I know there are fiberglass ones out there but they are just not the same as metal.

    Dan White
    64 R1 GT
    64 R2 GT
Working...
X