Hope it's ok to post this here.
South Bend Swap Meet: I need to unload a lot of miscellaneous parts and part of the list is below.
Let me know if anyone is interested in any of the following so I'll know if I need to haul them to SB. If you need a ball park price on an item(s), email me:
New Edelbrock carbs-500 and 600 cfm (New and remanufactured)
Aluminum radiator out of the '51
Stock '51 radiator
New Lark/T Cab radiator
T-86 with overdrive for '51 through '57
Same but with a Jeep top shifter
T-86 without overdrive
T-86 with overdrive for '58 through '66
Two T-10 four Speeds wide ratio early pattern and late pattern
Bell Housing for pick up trucks with three speed
New aluminum flywheel with 10.5 Clutch and disc
Powertrax Lock Right (this will turn your single pull rear into a Twin Traction)
Stock rebuilt rocker arms with shafts and stands ready to install
Roller rockers (Harland Sharp and Rocker Arm Specialists)
Ford 1.76 rockers made for Stude application
New Comp Roller Lifters
R oil pan with pan breather tube, special #4 main bolts and plate
Rebuilt V8 oil pumps (early & late)
Heads with R 3 valves, R 2+ springs, etc.
Lark fiberglass fenders ('61-'63)
Turning Wheels for the past several years PLUS Dick Datson publications, etc. (This stack measures about 20" high by 24" wide and 34" long!)
New and good used 44 axles
ATI V8 crank damper
Avanti Damper
Lark/Hawk R Damper
JTS bare block
Standard 289 pistons (nos)
AFB Intake Manifold
V8 header plates
Rebuilt 12 volt V8 starter for stick
Flightomatic transmission (worked when taken out but probably should be rebuilt)
Various ring and pinions (3.31, 4.27, 4.55, etc.)
Complete 44 rear ends
Disc brake set up
Trans adapter for GM trans.
Good Avanti gas tank
'51 intake manifold with carb
Miscellaneous motorcycle parts (spark plugs, chains, oil filters, etc.--CHEAP!)
Have several other items I'd like to sell but figure this list is plenty.
Ted
South Bend Swap Meet: I need to unload a lot of miscellaneous parts and part of the list is below.
Let me know if anyone is interested in any of the following so I'll know if I need to haul them to SB. If you need a ball park price on an item(s), email me:
New Edelbrock carbs-500 and 600 cfm (New and remanufactured)
Aluminum radiator out of the '51
Stock '51 radiator
New Lark/T Cab radiator
T-86 with overdrive for '51 through '57
Same but with a Jeep top shifter
T-86 without overdrive
T-86 with overdrive for '58 through '66
Two T-10 four Speeds wide ratio early pattern and late pattern
Bell Housing for pick up trucks with three speed
New aluminum flywheel with 10.5 Clutch and disc
Powertrax Lock Right (this will turn your single pull rear into a Twin Traction)
Stock rebuilt rocker arms with shafts and stands ready to install
Roller rockers (Harland Sharp and Rocker Arm Specialists)
Ford 1.76 rockers made for Stude application
New Comp Roller Lifters
R oil pan with pan breather tube, special #4 main bolts and plate
Rebuilt V8 oil pumps (early & late)
Heads with R 3 valves, R 2+ springs, etc.
Lark fiberglass fenders ('61-'63)
Turning Wheels for the past several years PLUS Dick Datson publications, etc. (This stack measures about 20" high by 24" wide and 34" long!)
New and good used 44 axles
ATI V8 crank damper
Avanti Damper
Lark/Hawk R Damper
JTS bare block
Standard 289 pistons (nos)
AFB Intake Manifold
V8 header plates
Rebuilt 12 volt V8 starter for stick
Flightomatic transmission (worked when taken out but probably should be rebuilt)
Various ring and pinions (3.31, 4.27, 4.55, etc.)
Complete 44 rear ends
Disc brake set up
Trans adapter for GM trans.
Good Avanti gas tank
'51 intake manifold with carb
Miscellaneous motorcycle parts (spark plugs, chains, oil filters, etc.--CHEAP!)
Have several other items I'd like to sell but figure this list is plenty.
Ted
[img=left]http://i158.photobucket.com/albums/t102/PlainBrownR2/My%201950%202r5%20Studebaker%20Pickup%20with%20turbocharger/P1000137-1.jpg[/img=left][img=right]http://i158.photobucket.com/albums/t102/PlainBrownR2/DSC00005.jpg?t=1171153370[/img=right]
Comment