Parts to South Bend ?

[Chicken Hawk]

Yes, I have one.

Ted

[quote]Originally posted by PlainBrownR2

Oh Ted,
Do you have any yokes that go on the rear of the T-10's? We're mighty interested in picking one up in SB.....

[PlainBrownR2]

Oh Ted,
Do you have any yokes that go on the rear of the T-10's? We're mighty interested in picking one up in SB.....

[img=left]http://i158.photobucket.com/albums/t102/PlainBrownR2/My%201950%202r5%20Studebaker%20Pickup%20with%20turbocharger/P1000137-1.jpg[/img=left][img=right]http://i158.photobucket.com/albums/t102/PlainBrownR2/DSC00005.jpg?t=1171153370[/img=right]

[bams50]

I'd sure like that Lark radiator! Too bad I can't make SB[V]



Robert (Bob) Andrews Owner- Studebakeracres- on the IoMT (Island of Misfit Toys!)
Parish, central NY 13131

"Some people live for the rules, I live for exceptions"- 311

"With your Lark you're on your own, free as a bird, alive as a Lark. You've suddenly discovered that happiness is a thing called Larking!"

[studebaker-R2-4-me]

Ted,

I would be interested in a Dana 44 Twin Traction, R Series oil pan and the Lark/Hawk Dampner. I am currently running 3.31:1 rear end. I want to take my car to the PSMCDR this September (hope it's warmer this year) I'm in the last stages of installing a Nimesh built R2 with a powershift in my 64 hawk. I would like to get my hands on a 3.73 or a 3.56 before September.

I'll be in South Bend for the swap meet



1964 GT Hawk R2 Clone
Oakville, Ontario.

Hamilton Chapter
See you at Niagara 2008 Crossroads Zone Meet July 18-20

[Chicken Hawk]

Hope it's ok to post this here.

South Bend Swap Meet: I need to unload a lot of miscellaneous parts and part of the list is below.

Let me know if anyone is interested in any of the following so I'll know if I need to haul them to SB. If you need a ball park price on an item(s), email me:

New Edelbrock carbs-500 and 600 cfm (New and remanufactured)

Aluminum radiator out of the '51

Stock '51 radiator

New Lark/T Cab radiator

T-86 with overdrive for '51 through '57

Same but with a Jeep top shifter

T-86 without overdrive

T-86 with overdrive for '58 through '66

Two T-10 four Speeds wide ratio early pattern and late pattern

Bell Housing for pick up trucks with three speed

New aluminum flywheel with 10.5 Clutch and disc

Powertrax Lock Right (this will turn your single pull rear into a Twin Traction)

Stock rebuilt rocker arms with shafts and stands ready to install

Roller rockers (Harland Sharp and Rocker Arm Specialists)

Ford 1.76 rockers made for Stude application

New Comp Roller Lifters

R oil pan with pan breather tube, special #4 main bolts and plate

Rebuilt V8 oil pumps (early & late)

Heads with R 3 valves, R 2+ springs, etc.

Lark fiberglass fenders ('61-'63)

Turning Wheels for the past several years PLUS Dick Datson publications, etc. (This stack measures about 20" high by 24" wide and 34" long!)

New and good used 44 axles

ATI V8 crank damper

Avanti Damper

Lark/Hawk R Damper

JTS bare block

Standard 289 pistons (nos)

AFB Intake Manifold

V8 header plates

Rebuilt 12 volt V8 starter for stick

Flightomatic transmission (worked when taken out but probably should be rebuilt)

Various ring and pinions (3.31, 4.27, 4.55, etc.)

Complete 44 rear ends

Disc brake set up

Trans adapter for GM trans.

Good Avanti gas tank

'51 intake manifold with carb

Miscellaneous motorcycle parts (spark plugs, chains, oil filters, etc.--CHEAP!)

Have several other items I'd like to sell but figure this list is plenty.

Ted