Announcement

Collapse
No announcement yet.

Need a High Numbers Dana 44

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Need a High Numbers Dana 44

    I would like to buy/trade/whatever, a high numbers Dana 44, TT rear end. I'm puttin' together a 1/8th mile, '60 Lark drag car.

    Thanks in advance!

    Sonny
    http://RacingStudebakers.com
    Sonny
    http://RacingStudebakers.com

  • #2
    Try Ted , Phill Harris or Meyers
    You going to run Auto or a Stick[?]

    Comment


    • #3
      Try Ted , Phill Harris or Meyers
      You going to run Auto or a Stick[?]

      Comment


      • #4
        Thanks Karl. I'm running a stick.

        Sonny
        http://RacingStudebakers.com
        Sonny
        http://RacingStudebakers.com

        Comment


        • #5
          Thanks Karl. I'm running a stick.

          Sonny
          http://RacingStudebakers.com
          Sonny
          http://RacingStudebakers.com

          Comment


          • #6
            Check SASCO, they still have a few Dana 44's kicking around.

            <h5>Mark
            '57 Transtar
            3E-6/7-122
            </h5>
            Mark Hayden
            '66 Commander
            Zone Coordinator
            Pacific Can-Am Zone


            Comment


            • #7
              Check SASCO, they still have a few Dana 44's kicking around.

              <h5>Mark
              '57 Transtar
              3E-6/7-122
              </h5>
              Mark Hayden
              '66 Commander
              Zone Coordinator
              Pacific Can-Am Zone


              Comment


              • #8
                Sonny,
                You probably want a LOW ratio (high numeric) rear end.



                Dick Steinkamp
                Bellingham, WA

                Comment


                • #9
                  Sonny,
                  You probably want a LOW ratio (high numeric) rear end.



                  Dick Steinkamp
                  Bellingham, WA

                  Comment


                  • #10
                    Sonny, Nelson Bove has a 4:89 TT Dana 60 truck axle on the Studebaker Swap page.Not quite what you are after,but I will mention it anyway.

                    Comment


                    • #11
                      Sonny, Nelson Bove has a 4:89 TT Dana 60 truck axle on the Studebaker Swap page.Not quite what you are after,but I will mention it anyway.

                      Comment


                      • #12
                        quote:Originally posted by Dick Steinkamp

                        Sonny,
                        You probably want a LOW ratio (high numeric) rear end.
                        Yes...

                        Sonny
                        http://RacingStudebakers.com
                        Sonny
                        http://RacingStudebakers.com

                        Comment


                        • #13
                          quote:Originally posted by Dick Steinkamp

                          Sonny,
                          You probably want a LOW ratio (high numeric) rear end.
                          Yes...

                          Sonny
                          http://RacingStudebakers.com
                          Sonny
                          http://RacingStudebakers.com

                          Comment


                          • #14
                            quote:Originally posted by ChampTrucking

                            Sonny, Nelson Bove has a 4:89 TT Dana 60 truck axle on the Studebaker Swap page.Not quite what you are after,but I will mention it anyway.
                            I sure appreciate the tip ChampTrucking! Only bad thing, it would take a whole-lot-a-massaging to get it under the Lark. Not that it can't be done, but I'm hoping to find something a little easier/lighter to get started.

                            Thanks again ChampTrucking!

                            Sonny
                            http://RacingStudebakers.com
                            Sonny
                            http://RacingStudebakers.com

                            Comment


                            • #15
                              quote:Originally posted by ChampTrucking

                              Sonny, Nelson Bove has a 4:89 TT Dana 60 truck axle on the Studebaker Swap page.Not quite what you are after,but I will mention it anyway.
                              I sure appreciate the tip ChampTrucking! Only bad thing, it would take a whole-lot-a-massaging to get it under the Lark. Not that it can't be done, but I'm hoping to find something a little easier/lighter to get started.

                              Thanks again ChampTrucking!

                              Sonny
                              http://RacingStudebakers.com
                              Sonny
                              http://RacingStudebakers.com

                              Comment

                              Working...
                              X