Announcement

Collapse
No announcement yet.

R2 AIR CLEANER BRACKET

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • R2 AIR CLEANER BRACKET

    LOOKING FOR #1558293 R2 AIR CLEANER BRACKET OR GOOD DRAWING WITH DIMENSIONS AND ANGLES
    THANKS
    PAUL LAUSCH

  • #2
    If you can't find a picture anywhere, try the Studebaker Museum. I think in their research department they have blueprints, etc. which they can copy and send to you for a fee.

    Joe Roberts
    '61 R1 Champ
    '65 Cruiser
    Editor of "The Down Easterner"
    Eastern North Carolina Chapter
    Joe Roberts
    '61 R1 Champ
    '65 Cruiser
    Eastern North Carolina Chapter

    Comment


    • #3
      Let me know the dimensions ,my R2 wagonaire was missing this piece. I would appreciate this.
      Thanks Tony

      Comment


      • #4
        Jeff has one floating around in my garage, from his R2 Daytona maybe he can help.

        JDP/Maryland
        JDP Maryland

        Comment


        • #5
          If Jeff has one floating around the garage, will he sell it to me when he catches it? Thanks very much for the replies.
          Paul Lausch

          Comment


          • #6
            Not for sale, it's part of his full package 64.

            JDP/Maryland
            JDP Maryland

            Comment


            • #7
              I'm sorry! I thought the car may have been dismantled and he had parts.Please provide pics and dimensions if possible. I hope I did not insult Jeff by misunderstanding.
              Thanks
              Paul Lausch

              Comment


              • #8
                Mavbe some detailed pictures. Perhaps even with a tape measure in the pix to show dimensions?

                sals54
                sals54

                Comment


                • #9
                  Does anyone have access to one of these brackets that they can measure? The next step on my R2 is to install the air cleaner assembly, and I am missing the bracket - if someone can provide the measurements, I am hoping I can make one which is similar.
                  Also, can someone provide measurements on where the holes are drilled on a R2 Lark for the air cleaner? My car had it's right fender replaced at some point.

                  thanks!

                  Eric DeRosa

                  '49 2R-5 (original Survivor)
                  '63 R2 Lark (barely surviving)
                  Eric DeRosa


                  \'63 R2 Lark
                  \'60 Lark Convertible

                  Comment


                  • #10
                    I'll ask Jeff when I see him.

                    JDP/Maryland
                    JDP Maryland

                    Comment


                    • #11
                      A photo is worth a 1000 words, here are 3000 + words. Photos are from my 63 Daytona R2.



                      The black bracket is about 1 inch wide and 7 1/4 inches total length, the top bend is 1 1/14 inch, the bottom bend (two holes) is 2 inches. The rear of the air cleaner is about 5 1/4 inches from the body tag on the cowl. The PCV elbow is about 1/2 inch below the pole that is laid accross the top of the front fenders.


                      34 STUDEBAKER STREET ROD
                      55 SPEEDSTER (in work)
                      63 R2 LARK (in work)
                      85 AVANTI (9K miles)

                      34 Studebaker Street Rod (completed)
                      55 Speedster (in work)
                      63 Lark R2 (completed, 63K miles)
                      64 Daytona CNV (completed, 63K miles)
                      64 Avanti R2 (completed)
                      85 Avanti(blackout trim, 10K miles)
                      89 Avanti CNV (19K miles)

                      Comment


                      • #12
                        Jackson,

                        THANKS That's what I needed!

                        Eric DeRosa

                        '49 2R-5 (original Survivor)
                        '63 R2 Lark (barely surviving)
                        Eric DeRosa


                        \'63 R2 Lark
                        \'60 Lark Convertible

                        Comment


                        • #13
                          Thank you also! That should be enough info to get the job done.
                          THANKS AGAIN
                          PAUL LAUSCH

                          Comment


                          • #14
                            Forgot to ask you the thickness. It looks like 3/16"
                            Thanks
                            PAUL LAUSCH

                            Comment


                            • #15
                              quote: Forgot to ask you the thickness. It looks like 3/16"
                              Thickness is 1/8 inch.


                              34 STUDEBAKER STREET ROD
                              55 SPEEDSTER (in work)
                              63 R2 LARK (in work)
                              85 AVANTI (9K miles)

                              34 Studebaker Street Rod (completed)
                              55 Speedster (in work)
                              63 Lark R2 (completed, 63K miles)
                              64 Daytona CNV (completed, 63K miles)
                              64 Avanti R2 (completed)
                              85 Avanti(blackout trim, 10K miles)
                              89 Avanti CNV (19K miles)

                              Comment

                              Working...
                              X