Announcement

Collapse
No announcement yet.

Ute axles

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Ute axles

    I installed new inner seals in the rear end of the Ute and slipped the axles back in. That's when I noticed that BOTH axles were slightly twisted where the key ends up in the keyway...





    It's a little strange that BOTH were twisted since the car has an open rear end (factory 4.56/1).

    Although Lee had a Supercharged Golden Hawk engine in the car, I don't think it would have done this kind of damage to the axles. When I got the car, it had indications that a brand x engine was installed sometime after Lee sold it. It must have been a little TOO big OR someone had sidestepped the clutch at 4,000 RPMs too often.

    I've got one good extra 44 axle in inventory, but need another. Anybody near this corner of the US have an extra?



    Dick Steinkamp
    Bellingham, WA



    Dick Steinkamp
    Bellingham, WA

  • #2
    I have a couple I could donate Dick but am too far away I'm afraid.
    Frank van Doorn
    Omaha, Ne.
    1962 GT Hawk 289 4 speed
    1941 Champion streetrod, R-2 Powered, GM 200-4R trans.
    1952 V-8 232 Commander State "Starliner" hardtop OD

    Comment


    • #3
      quote:Originally posted by 41 Frank

      I have a couple I could donate Dick but am too far away I'm afraid.
      Thanks, Frank.

      Dick Steinkamp
      Bellingham, WA



      Dick Steinkamp
      Bellingham, WA

      Comment


      • #4
        Is it possible that the damage was done to the axles because the axle nuts were not torqued properly at some point in its life?
        Frank van Doorn
        Omaha, Ne.
        1962 GT Hawk 289 4 speed
        1941 Champion streetrod, R-2 Powered, GM 200-4R trans.
        1952 V-8 232 Commander State "Starliner" hardtop OD

        Comment


        • #5
          I will be home tomorrow, and I'll have a look at the rear axle that came with your engine. It was an Automatic Drive car, so the axles may be good. I don't think I have any loose axles for a 44.

          Gord Richmond, within Weasel range of the Alberta Badlands
          Gord Richmond, within Weasel range of the Alberta Badlands

          Comment


          • #6
            Dick , I have one.Left over from flanged swap.

            Comment


            • #7
              Thanks Karl and Gord. I'll let you know if I strike out locally.



              Dick Steinkamp
              Bellingham, WA



              Dick Steinkamp
              Bellingham, WA

              Comment


              • #8
                Dick, I have at least two, and you're welcome to have one of them if you want. I'm in North Vancouver, BC, but I'll be going through Bellingham within the next week or so with two other Studes to drop them off for transport to the 2008 Carrera in Mexico. I could throw the axle in and maybe meet you at a convenient rest stop? or somewhere easy to exit and re-enter the I5?

                John
                1953 Commander Coupe
                1954 Champion Sedan
                1963 Lark

                John
                1953 Commander Coupe
                1954 Champion Sedan
                1963 Lark

                Comment


                • #9
                  quote:Originally posted by jngregory

                  Dick, I have at least two, and you're welcome to have one of them if you want. I'm in North Vancouver, BC, but I'll be going through Bellingham within the next week or so with two other Studes to drop them off for transport to the 2008 Carrera in Mexico. I could throw the axle in and maybe meet you at a convenient rest stop? or somewhere easy to exit and re-enter the I5?

                  That sounds great, John!

                  I'll email you through forum mail to make arrangements. If for some reason the forum mail doesn't go through, my email is ddstnkmp@yahoo.com



                  Dick Steinkamp
                  Bellingham, WA



                  Dick Steinkamp
                  Bellingham, WA

                  Comment

                  Working...
                  X